You must log in to edit PetroWiki. Help with editing

Content of PetroWiki is intended for personal use only and to supplement, not replace, engineering judgment. SPE disclaims any and all liability for your use of such content. More information

# Diagnostic plots

The diagnostic plot is a log-log plot of the pressure change and pressure derivative (vertical axis) from a pressure transient test vs. elapsed time (horizontal axis).

**Fig. 1** shows an example of a diagnostic plot. The diagnostic plot can be divided into three time regions: early, middle, and late. At the earliest times on a plot (the early-time region), wellbore and near-wellbore effects dominate. These effects include wellbore storage, formation damage, partial penetration, phase redistribution, and stimulation (hydraulic fractures or acidization). At intermediate times (the middle-time region), a reservoir will ordinarily be infinite acting. For a homogeneous reservoir, the pressure derivative will be horizontal during this time region. Data in this region lead to the most accurate estimates of formation permeability. At the latest times in a test (the late-time region), boundary effects dominate curve shapes. The types of boundaries that may affect the pressure response include sealing faults, closed reservoirs, and gas/water, gas/oil, and oil/water contacts. Several common flow regimes and the diagnostic plots associated with these flow regimes are discussed here.

## Contents

## Volumetric behavior

Volumetric behavior is defined as that pressure response time dominated by the wellbore, reservoir, or part of the reservoir acting like a uniform-pressure "tank" with fluid entering or leaving the tank. The most common example of volumetric behavior is wellbore storage, which dominates during the early-time region. The "tank" is the wellbore, in which the pressure is uniform. Fluid either leaves this tank (earliest times in a flow test, before the reservoir begins to respond) or enters the tank (earliest times in a buildup test). Another example is pseudosteady-state (boundary-dominated) flow in a closed reservoir during constant-rate production. In this case, the reservoir is the tank; pressure is changing at the same rate throughout (although it is not the same at all points), and fluid is leaving the reservoir through the producing well. As a final example, in a test the reservoir may behave like a tank with recharge (fluid influx) entering from a secondary source of pressure support, such as a large supply of hydrocarbons in a lower-permeability medium in pressure communication with the reservoir being tested.

The equation modeling wellbore storage (derived from a mass balance on the wellbore) is

The equation modeling pseudosteady-state flow in a cylindrical drainage area is

The general form is

The derivative of the general form is

The implication is that the derivative plot will have unit slope (up one log cycle as it moves over one log cycle) on log-log coordinates, and the pressure change plot will approach unity at long times when b v is not equal to zero (**Fig. 2**). In wellbore storage, *b*_{v} is zero, and the derivative and pressure change plots will lie on top of one another. During pseudosteady-state flow or recharge, the pressure change and pressure derivative plots will not coincide.

## Radial flow

Infinite-acting radial flow is common in reservoirs, and data in the radial flow regime can be used to estimate formation permeability and skin factor. Common situations in which radial flow occurs include flow into vertical wells after wellbore storage distortion has ceased and before boundary effects, hydraulically fractured wells after the transient has moved well beyond the tips of the fracture, horizontal wells before the transient has reached the top and bottom of the productive interval, and horizontal wells after the transient has moved beyond the ends of the wellbore.

The equation used to model radial flow for a well producing at constant rate is the familiar logarithmic approximation to the line-source solution,

Equations modeling radial flow have the general form

with derivative

On the diagnostic plot (**Fig. 3**), radial flow is indicated by a horizontal derivative.

## Linear flow

Linear flow is also common and occurs in channel reservoirs, hydraulically fractured wells, and horizontal wells. Data from linear flow regimes can be used to estimate channel width or fracture half-length if an estimate of permeability is available. In horizontal wells, an estimate of permeability perpendicular to the well can be made if the productive well length open to flow is known.

An equation that models linear flow in a channel reservoir of width *w* is

For a hydraulically fractured well with fracture half-length *L*_{f},

The general form is

The derivative is

Linear flow on the diagnostic plot is indicated when a derivative follows a half-slope line—that is, a line that moves up vertically by one log cycle for each two cycles of horizontal movement (**Fig. 4**). The pressure change may or may not also follow a half-slope line. In a hydraulically fractured well, the pressure change will follow a half-slope line unless the fracture is damaged. In a channel reservoir, a hydraulically fractured well with damage, or a horizontal well, the pressure change will approach the half-slope line from above.

## Bilinear flow

Bilinear flow occurs primarily in wells with low-conductivity hydraulic fractures. Flow is linear within the fracture to the well, and also linear (normal to fracture flow) from the formation into the fracture. Estimates of fracture conductivity, *w*_{f}*k*_{f}, can be made with data from this flow regime when estimates of formation permeability are available.

For a hydraulically fractured well, an equation that models bilinear flow is

The general form is

The derivative is

Bilinear flow derivatives plot as a quarter-slope line on the diagnostic plot (**Fig. 5**). The quarter-slope line moves up one log cycle as it moves over four log cycles. The pressure change does not necessarily follow a quarter-slope line. In a damaged, hydraulically fractured well, the pressure change curve will approach the quarter-slope line from above; in an undamaged hydraulically fractured well (Δ*p*_{s} = 0), the pressure change will typically follow the quarter-slope line when the effects of wellbore storage have ended.

## Spherical flow

The flow pattern is spherical when the pressure transient can propagate freely in three dimensions and converge into a "point." This can occur for wells that penetrate only a short distance into the formation (actually hemispherical flow), wells that have only a limited number of perforations open to flow, horizontal wells with inflow over only short intervals, and during wireline formation tests. Data in the spherical-flow regime can be used to estimate the mean permeability,

An equation that models spherical flow is

where ....................(17)

and *r*_{sp} is the radius of the sphere into which flow converges. The general form is

and the derivative is

Spherical flow on the diagnostic plot produces a derivative line with a slope of −1/2. The pressure change during spherical flow approaches a horizontal line from below, and never exhibits a straight line with the same slope as the derivative (**Fig. 6**). Spherical flow can occur during either buildup or drawdown tests.

## Flow regimes on the diagnostic plot

A major application of the diagnostic plot is the potential that it provides in identifying the flow regimes that appear in a logical sequence during a buildup or flow test. For example, consider **Fig. 7**. At early times, the unit slope line on both derivative and pressure change, indicating wellbore storage. Later, a derivative with a slope of −1/2, indicating possible spherical flow, followed by a horizontal derivative, indicating infinite-acting radial flow. Boundary effects, including a unit-slope line, follow, indicating possible recharge of the reservoir pressure.

## Nomenclature

## Noteworthy papers in OnePetro

Use this section to list papers in OnePetro that a reader who wants to learn more should definitely read

## External links

Use this section to provide links to relevant material on websites other than PetroWiki and OnePetro

## See also

Fluid flow through permeable media

Boundary effects in diagnostic plots

Estimating average reservoir pressure from diagnostic plots

Flow equations for gas and multiphase flow

PEH:Fluid_Flow_Through_Permeable_Media